The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
We've stumbled on the article about How to Install a Bathtub listed below on the web and accepted it made good sense to talk about it with you on this site.
Mounting a bathtub isn't precisely rocket science, however it does need solid plumbing, woodworking, and often, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately difficult job. If the old tub is conveniently obtainable, the project can relocate easily; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will require an assistant to vacate the old tub and also set in the brand-new one. Make sure you have certified on your own for the work and also are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is far better to consider employing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This post will help you set up a new tub in your shower room if you have actually already bought a brand-new tub and also do not need to change the plan of your previous water system pipes.
Your devices and product list ought to consist of the following:
Getting ready for the Installation
First of all, the sustaining frame provided with the bath needs to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be quite troublesome due to the restricted access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are practical in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bath tub till the spirit level checks out level.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the tub as well as likewise inspect the overflow outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait until the tub has been made use of at the very least once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in area between the faucet as well as the sink. Secure the tap in place with the supplier provided backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the tub with water prior to sealing, to allow for the movement experienced when the tub remains in use. The sealer can break fairly early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the market. It is advisable to fit the floor tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Hopefully you liked our topic on Tools You Need to Install a New Bathtub . Thank you so much for spending some time to read our content. Appreciated our piece? Please share it. Help someone else locate it. We thank you for reading our article about How to Install a Bathtub Yourself.
Premium service for plumbing emergencies. Report this page